SD MARINE BUILD PRIMER High-build Alkyd Primer is an alkyd coating used as a primer. For steel structure surfaces in non-immersed areas. An anti-corrosive primer based on long-oil alkyd resin and anti-corrosive pigments. Good anti-corrosive performance; Compatibility with alkyd finish systems; Good workability. Specifications on this page: volume solids 57 ± 2%, DFT 50-100 µm per coat, theoretical spreading rate 11.4 m²/L. Comparable products of the same brand and type: ALKFEND PRIMER 30 Alkyd Primer 30, SD MARINE PRIMER Alkyd Primer, AMEINCOAT ZINC PRIMER Container Zinc-rich Primer.
Source: KANSAI original technical data sheet (TDS) "SD MARINE BUILD PRIMER Alkyd High-build Primer"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 57 ± 2% |
|---|---|
| Dry Film Thickness | 50–100 µm per coat |
| Theoretical Spreading Rate | 11.4 m²/L/50 µm |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Flash Point | Above 38 °C |
| Thinner | Dedicated thinner |
| Mixing Ratio | Single-component coating |
| SD MARINE BUILD PRIMER | Alkyd high-build primer |
|---|
A rust preventive primer based on long oil alkyd resin and anti-rust pigments.
For steel structure in non immersion areas.
Good corrosion resistance
| Color | Oxide Red, Grey |
|---|---|
| Colour | Iron red, grey |
| Volume Solids | 57±2% |
| Flash Point | Greater than 38°C |
| Flash Point | Above 38 °C |
| Film thickness | Dry : 50-100 microns/coat Wet : 88-176microns/coat |
| Applied film thickness | Dry film: 50–100 µm/coat; wet film: 88–176 µm/coat |
| Theoretical Coverage | 11.4m2/Ltr/50 microns |
| Theoretical Spreading Rate | 11.4 m²/L/50 µm |
Practical coverage depending on surface conditions, environment, applications, etc.
| SURFACE PREPARATION | Remove salt and other water-soluble contaminants by fresh water. |
|---|---|
| Surface Preparation | Rinse off salts and other water-soluble contaminants with clean water. |
Remove oil and grease with suitable detergent or solvent(SSPC-SP-1).
Remove rust, mill-scale and other loose material completely by abrasive blasting.
All surface to be coated should completely clean,dry and free from contamination.
| Application Temperature | -5°C-40°C |
|---|---|
| Mixing | Mix thoroughly with power agitator |
| Mixing | Stir thoroughly with a power tool |
| Mixing Ratio | One component coating |
| Mixing ratio | Single-component coating |
| Application Methods | Airless spray, air spray, brush and roller |
| Application Methods | Airless spray, air spray, brush, roller |
| Nozzle tip | Nozzle size | 0.43mm-0.53mm |
| Nozzle pressure | Output pressure | ≥10Mpa |
| Thinning ratio | 0–10% by weight |
Brush/Roller; Thinning ratio 0–10% by weight
| Thinner | SD MARINE Paint Thinner |
|---|---|
| Thinner | Dedicated thinner |
| Drying time & Overcoating interval | Drying time & Surface dry | Drying time & touch dry | -5°C 4hrs | 5°C 2hrs | 20°C 1hr | 30°C 30mins |
| Drying time & recoat interval | Touch dry | Semi-hard dry | 16hrs | 10hrs | 6hrs | 4hr |
| Min. interval | Minimum recoat interval | 36hrs | 24hrs | 10hrs | 8hrs | |
| Max. interval | Maximum recoat interval |
| Applied substrates | Bare steel |
|---|---|
| Suitable substrates | Bare steel |
| Typical topcoat | SD MARINE BTD or according to the coating system of Cosco Kansai. |
| Suitable for overcoating | Alkyd topcoat, or refer to our coating system |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
| Shelf life | 12months from date of production (25°C) |
|---|---|
| Shelf life | 12 months from date of production (25 °C) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
The information provided in this data sheet is, to the best of our knowledge, the most complete and accurate information currently available. As the conditions of product use are beyond our control, this information carries no warranty, and we are responsible to the buyer only in the selection of the product. As our products and production processes are continuously developed, the content of this data sheet is subject to change at any time, and all information herein is subject to our confirmation. Confirm that the data sheet in hand is the latest version before using the product.
| Issued Date | 2025/1 |
|---|
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
