EPOMARINE SEALER PRIMER epoxy sealer is an epoxy coating used as a primer. For moderate to severe corrosive environments: used in moderate to severe corrosive environments as a sealer over inorganic zinc coatings or similar substrates/coatings to prevent blistering of the film. A two-component polyamide-cured epoxy coating with excellent penetration into porous primers such as inorganic zinc primers. Excellent penetration and tough, strong films. Parameters on this page: volume solids 50 ± 2%, dry film thickness 20-40 µm per coat, theoretical spreading rate 0.067 kg/m²/25 µm.
Parameter source: KANSAI original technical data sheet (TDS) “EPOMARINE SEALER PRIMER Epoxy Sealer”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 50 ± 2% |
|---|---|
| Dry Film Thickness | 20–40 µm/coat |
| Theoretical Spreading Rate | 0.067 kg/m²/25 µm |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Flash Point | Above 23 °C |
| Thinner | Epoxy Thinner #20 |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| EPOMARINE SEALER PRIMER | Epoxy Sealer |
|---|
a two-component polyamide cured epoxy paint with excellent penetrating performance to the
As a sealer to apply on cured inorganic zinc coating or similar surfaces to avoid popping in
Complies with JT/T 722-2008
Excellent penetrating performance
| Color | Grey |
|---|---|
| Colour | Grey |
| Volume Solids | 50±2% |
| Flash Point | Greater than 23°C |
| Flash Point | Above 23 °C |
| Film thickness | Dry20-40 microns/coat Wet : 40-80microns/coat |
| Applied film thickness | Dry film: 20–40 µm/coat Wet film: 40–80 µm/coat |
| Theoretical Coverage | 0.067Kg/m2/25 microns |
| Theoretical spreading rate | 0.067 kg/m²/25 µm |
Practical coverage depending on surface conditions, environment, applications, etc.
| Application Temperature | 5°C-40°C |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| Mixing | Mix the base and curing agent and stir thoroughly with a power tool |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| Mixing ratio | Base : curing agent = 9:1 (by mass) |
| Pot life | 5°C | 20°C | 30°C |
| Pot life | 16hrs | 8hrs | 4hrs |
| Application Methods | Airless spray, air spray |
|---|---|
| Application Methods | Airless spray, air spray |
Airless spray
| Nozzle tip | Nozzle size | 0.43mm-0.53mm |
| Nozzle pressure | Output pressure | ≥15Mpa |
| Thinning ratio | 20–30% by volume |
| Thinner | Epomarine Thinner #20 |
|---|---|
| Thinner | Epoxy Thinner #20 |
| Drying time & Overcoating interval | Drying time & Surface dry | Drying time & touch dry | 10°C 3hrs | 20°C 2hrs | 30°C 2hr |
| Drying time & recoat interval | Touch dry | Semi-hard dry | 30hrs | 16hrs | 12hrs |
| Min. interval | Minimum recoat interval | 30hrs | 16hrs | 12hrs | |
| Max. interval | Maximum recoat interval |
| Typical undercoat | SD ZINC 1500N, metal zinc spray |
|---|---|
| Suitable for undercoating | Inorganic Zinc-Rich Primer 1500N, hot-sprayed zinc |
| Typical topcoat | UNIVERSAL EP-60 or according to the coating system of Cosco Kansai. |
| Suitable for overcoating | General-purpose epoxy micaceous iron oxide coating EP-60, or refer to our coating systems |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
| Shelf life | 12 months from date of production (25°C) |
|---|---|
| Shelf life | 12 months from date of production (25 °C) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
The information provided in this data sheet is, to the best of our knowledge, the most complete and accurate information currently available. As the conditions of product use are beyond our control, this information carries no warranty, and we are responsible to the buyer only in the selection of the product. As our products and production processes are continuously developed, the content of this data sheet is subject to change at any time, and all information herein is subject to our confirmation. Confirm that the data sheet in hand is the latest version before using the product.
| Issued Date | 2019/05 |
|---|
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
