Red Lead Phenolic Anticorrosive Paint F53-31 is a phenolic coating used as a primer. Suitable for use as an anticorrosive paint on land-based steel structures and on ship areas above the waterline, and can be used with traditional topcoats such as phenolic and alkyd. A phenolic red lead anticorrosive paint formulated from phenolic vehicle, red lead powder, driers, additives and solvents. Parameters on this page: volume solids 53 ± 3%, dry film thickness 40 µm, theoretical spreading rate 152 g/m².
Parameter source: KAILIN original technical data sheet (TDS) for Red Lead Phenolic Anticorrosive Paint F53-31; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 53 ± 3% |
|---|---|
| Dry Film Thickness | 40µm |
| Theoretical Spreading Rate | 152 g/m² |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 34°C |
| Thinner | Thinner 104 |
| Colour / Appearance | Orange-red, flat film |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
| Composition | A phenolic red lead anticorrosive paint formulated from phenolic vehicle, red lead powder, driers, additives and solvents |
|---|
Suitable for use as an anticorrosive paint on land-based steel structures and on ship areas above the waterline, and can be used with phenolic, alkyd
and other traditional topcoats.
| Appearance | Orange-red, flat film |
|---|
| Volume Solids | 53 ± 3% (measured according to GB/T 9272 eqv ISO 3233:1998) |
|---|---|
| Dry Film Thickness | 40µm |
| Wet Film Thickness | 75µm |
| Theoretical quantity | 152g/m² |
| Flash Point | 34°C |
| Drying time (25 °C) | Surface dry ≤ 5 h; hard dry ≤ 24 h |
| Recoat interval | |||
| Temperature | 5°C | 20°C | 30°C |
| Minimum | 48h | 24h | 16h |
| Maximum | 3 months | ||
| Recommended number of coats | 2 coats, dry film thickness above 80 µm |
|---|---|
| Subsequent coat | Various phenolic and alkyd topcoats |
Mill-scale-free steel: abrade with air-driven or power grinding tools to St3, or blast clean to Sa2
Shop-primed steel: re-prepare damaged and rusted film areas, abrading to St 3
Welded, flame-cut or heat-corrected areas: grind to St 3
Substrates with existing coating (same type): remove loose, failed old coating and rust; prepare with pneumatic or power grinding tools to St 3
| Airless Spray | |
| Thinner | Thinner 104 |
| Thinning quantity | 0–5% (by paint weight) |
| Nozzle tip size | 0.4-0.5mm |
| Spray output pressure | 12–15 MPa (approx. 120–150 kg/cm²) |
| Air Spray | |
| Thinner | Thinner 104 |
| Thinning quantity | 0–10% (by paint weight) |
| Nozzle tip size | 2.0-3.0mm |
| Air pressure | 0.3–0.4 MPa (approx. 3–4 kg/cm²) |
| Thinner | Thinner 104 |
|---|---|
| Thinning quantity | 0–3% (by paint weight) |
| Cleaning solvent | Thinner 104 |
| Safety measures | See the Safety Data Sheet (MSDS) of Shanghai Kailin Paint Factory. |
| Packaging | 18 kg in a 10 L drum |
| Shelf Life | 12 months |
It cannot be used alone (poor weather resistance); it must be used with a topcoat.
The red lead paint film should not be exposed to air for too long, otherwise the film is prone to whitening or discolouration.
Red lead paint is not suitable for prolonged immersion and shall not be used on the waterline or hull bottom
As the film contains red lead, it is not suitable for use in enclosed spaces where flame straightening is carried out, to prevent lead poisoning
| Notes | To use this product correctly, read the Application Guide in this data sheet carefully. |
|---|
The above information and data for this product are accumulated from our tests and practical experience
accumulated, and may serve as an application guide. For application carried out under conditions unknown to us, we
We guarantee only the quality of the paint itself and accept no responsibility for other matters. We
and reserve the right to make modifications as the product is improved.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
