Iron Oxide Alkyd Primer C06-1 belongs to alkyd coatings and is used as a primer. It is intended for use as a priming coat on steel surfaces to be topcoated with nitrocellulose topcoat or alkyd topcoat. It is formulated from medium-oil-length drying vegetable oil alkyd resin, iron oxide red and other anti-corrosive pigments, extender pigments, driers, additives and solvents. It exhibits good nitrocellulose resistance; when used with nitrocellulose coatings, it does not lift or bleed. Durability is good under normal climatic conditions, but poor under hot and humid conditions. Parameters on this page: volume solids 36 ± 3%, dry film thickness 35 µm, theoretical spreading rate 137 g/m².
Parameter source: KAILIN original technical data sheet (TDS) “Iron Oxide Alkyd Primer C06-1”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 36 ± 3% |
|---|---|
| Dry Film Thickness | 35µm |
| Theoretical Spreading Rate | 137 g/m² |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 40°C |
| Thinner | Thinner 104 |
| Colour / Appearance | Iron oxide red, tone indeterminate, film smooth |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Formulated from medium-oil-length drying vegetable oil alkyd resin, iron oxide red and other anti-corrosive pigments, extender pigments, driers,
additives and solvents.
Good nitrocellulose resistance; when used with nitrocellulose coatings, does not lift or bleed
Durability is good under normal climatic conditions, but poor under hot and humid conditions
| Use | Intended for use as a priming coat on steel surfaces to be topcoated with nitrocellulose topcoat or alkyd topcoat. |
|---|---|
| Appearance | Iron oxide red, tone indeterminate, film smooth. |
| Volume Solids | 36 ± 3% (determined in accordance with GB/T 9272 eqv ISO 3233:1998) |
|---|---|
| Dry Film Thickness | 35µm |
| Wet Film Thickness | 97µm |
| Theoretical quantity | 137g/m² |
| Flash Point | 40°C |
| Drying time (25 °C) | Touch dry ≤ 2 h, hard dry ≤ 24 h, stoving (105 ± 2 °C) ≤ 30 min |
| Recoat interval | |||
| Temperature | 5°C | 20°C | 30°C |
| Minimum | 48h | 24h | 20h |
| Maximum | Unlimited | ||
| Recommended number of coats | 2 coats, dry film thickness 70 µm |
|---|---|
| Subsequent coat | Nitrocellulose coatings and various oil-based, phenolic and alkyd topcoats, alkyd deck anti-slip coating |
Steel with mill scale: blast cleaning to Sa2 grade (pickling may also be used to remove mill scale and rust completely)
Mill-scale-free steel: grind with abrasive discs to St 3
Shop-primed steel: re-prepare damaged and rusted film areas, abrading to St 3
Welded, flame-cut or heat-corrected areas: grind to St 3
| Airless Spray | |
| Thinner | Thinner 104 |
| Thinning quantity | 0–5% (by paint weight) |
| Nozzle tip size | 0.4-0.5mm |
| Spray output pressure | 12–15 MPa (approx. 120–150 kg/cm²) |
| Air Spray | |
| Thinner | Thinner 104 |
| Thinning quantity | 0–10% (by paint weight) |
| Nozzle tip size | 2.0-3.0mm |
| Air pressure | 0.3–0.4 MPa (approx. 3–4 kg/cm²) |
| Roller/brush | Thinner: Thinner 104; dilution: 0–5% (by paint weight) |
|---|---|
| Cleaning solvent | Thinner 104 |
| Safety measures | See the Safety Data Sheet (MSDS) of Shanghai Kailin Paint Factory. |
| Packaging | 25 kg in a 20 L drum |
| Shelf Life | 12 months |
| Notes | To use this product correctly, read the Application Guide in this data sheet carefully. |
The above information and data for this product are accumulated from our tests and practical experience
accumulated, and may serve as an application guide. For application carried out under conditions unknown to us, we
| Only oil is guaranteed | The quality of the paint itself; no responsibility is accepted for issues in other respects. Regarding this instruction, |
|---|
the right is reserved to make modifications based on continuous product improvement.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
