SeaForce SPL Hydrolysis Self-Polishing Antifouling SPL is an antifouling. Marine coatings: recommended only for markings on underwater hulls in newbuilding and repair projects. It is a one-component acrylic resin hydrolysis antifouling based on ion-exchange technology. Parameters on this page: volume solids 55 ± 2%, dry film thickness 40-100 µm, theoretical spreading rate 13.7-5.5 m²/L. Comparable models from the same brand: SeaConomy 700 self-polishing antifouling 700, SeaConomy 900 self-polishing antifouling 900, SeaForce 30 M hydrolysis self-polishing antifouling 30M.
Parameter source: JOTUN original technical data sheet (TDS) for SeaForce SPL Hydrolysis Self-Polishing Antifouling SPL; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 55 ± 2% |
|---|---|
| Dry Film Thickness | 40–100 µm |
| Theoretical Spreading Rate | 13.7-5.5 m²/L |
| VOC | 409 g/L (US) |
| Density / Specific Gravity | 1.5 kg/L |
| Number of Components | One-component |
| Flash Point | 28 °C |
| Thinner | JOTUN Thinner No. 7 / JOTUN Thinner No. 10 |
| Wet Film Thickness | 75-180 µm |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Hydrolysable Self-Polishing Antifouling SPL
It is a one-component acrylic resin hydrolysis antifouling based on ion-exchange technology. It has very good antifouling performance. Used as a topcoat for specified antifouling coatings. It can be applied at surface temperatures below 0 °C.
Marine coatings:
Recommended only for markings on underwater hulls in newbuilding and repair projects. Specifically for vessels of various speeds and high operating rates.
Antifouling.
Complies with the IMO Antifouling Systems Convention AFS/CONF/26 and IMO MEPC.331(76)
Other certificates and approvals are available on request.
White
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 55± 2 % |
| Flash Point | ISO 3679 Method 1 | 28 °C |
| Density | Theoretical Value | 1.5 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| US | CARB(SCM)2020 / SCAQMD rule 1113 | Calculation | 409 g/L |
| Hong Kong | Air Pollution Control (VOC) Regulation | Calculation | 409 g/L |
| EU | European Paint Directive 2004/42/CE | Calculation | 409 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
Typical recommended specification range
| Dry Film Thickness | 40–100 µm |
| Wet Film Thickness | 75-180 µm |
| Theoretical Spreading Rate | 13.7-5.5 m²/L |
Surface Preparation
| Substrate | Minimum | Recommended |
| Coated surface | New tie coat or antifouling: remove any contamination affecting adhesion of the intermediate coat. | |
| Exceeding the maximum recoat interval may require cleaning, abrading or the use of another coating, as appropriate. | ||
| Aged antifouling coatings with a leached layer: | ||
| Rinse thoroughly with fresh water at a minimum nozzle pressure of 200 bar | Rinse thoroughly with fresh water at a minimum nozzle pressure of 340 bar | |
| remove. | ||
This product may be applied by the following methods
| Brush: | Ensure that the specified dry film thickness is achieved. |
| Roller: | May be used. Ensure the specified dry film thickness is achieved. |
One-component
| Thinner | JOTUN Thinner No. 7 / JOTUN Thinner No. 10 |
|---|
In China, the cleaning solvent must comply with GB 38508-2020
| Substrate Temperature | -10 °C | 0 °C | 5 °C | 10 °C | 23 °C | 40 °C |
| Touch Dry | 5 h | 2 h | 1 h | 45 min | 30 min | |
| Minimum recoat interval | 48 h | 36 h | 12 h | 9 h | 7 h | 6 h |
| Dry/cured to immersion | 48 h | 36 h | 12 h | 10 h | 8 h | |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
When three or more coats of antifouling are applied in rapid succession, the recommended time before immersion should be doubled.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Dry/cured to immersion: the minimum time before the coating can be permanently immersed in sea water.
| Volume | Container Size | |
| (L) | ||
| Hydrolysable Self-Polishing Antifouling SPL | 5 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Hydrolysis Self-Polishing Antifouling SPL 24 months
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
