Pilot QD Primer Plus High-Build Modified Alkyd Primer is an alkyd coating used as a primer. Marine coatings: recommended for engines, freeboards, decks and superstructures. It is a high-build product that is fast-drying and contains zinc phosphate pigment. Parameters on this page: volume solids 56 ± 2%, dry film thickness 40-125 µm, theoretical spreading rate 14-4.5 m²/L. Comparable models from the same brand: Alkydprimer alkyd primer, Jota AK15P fast-drying alkyd primer AK15P, Pilot QD Primer fast-drying alkyd primer.
Parameter source: JOTUN original technical data sheet (TDS) for Pilot QD Primer Plus High-Build Modified Alkyd Primer; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 56 ± 2% |
|---|---|
| Dry Film Thickness | 40–125 µm |
| Theoretical Spreading Rate | 14–4.5 m²/L |
| VOC | 353 g/L (China) |
| Density / Specific Gravity | 1.6 kg/L |
| Number of Components | One-component |
| Flash Point | 26 °C |
| Thinner | Summer use |
| Gloss | Matt (0–35) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Pilot QD Primer Plus
This is a single-component oxidatively drying alkyd coating. It is a high-build product with fast drying and zinc phosphate pigmentation. It may be used as a primer or intermediate coat in atmospheric environments. Suitable for properly prepared carbon steel, aluminium and wood substrates.
Marine coatings:
Recommended for engines, topsides, decks and superstructures.
Others
Certified compliant with the low flame-spread requirements of the IMO 2010 FTP Code. For details, consult your JOTUN representative.
Other certificates and approvals are available on request.
Grey XO, grey, red
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 56± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 26 °C |
| Density | Theoretical Value | 1.6 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| US | CARB(SCM)2020 / SCAQMD rule 1113 | Calculation | 357 g/L |
| Hong Kong | Air Pollution Control (VOC) Regulation | Calculation | 357 g/L |
| EU | European Paint Directive 2004/42/CE | Calculation | 357 g/L |
| China | Mandatory national standard of China | GB 30981.2-2025 | 353 g/L |
| Coating hazards GB | 30981.2-S-Pb≤1000-NC |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 40–125 µm |
| Wet Film Thickness | 70–220 µm |
| Theoretical Spreading Rate | 14–4.5 m²/L |
| Theoretical Spreading Rate | 8.8-2.8 m²/kg |
Surface Preparation
| Substrate | Minimum | Recommended |
| Carbon Steel | St 2 (ISO 8501-1) | Sa 2½ (ISO 8501-1) |
| Aluminium | The surface should be blasted with a non-metallic abrasive, | “Blast clean using an approved non-metallic abrasive |
| hand- or machine-sanded using abrasive paper or fibre discs, | to produce a sharp angular surface profile.” |
to produce scratch marks on the surface.
| Wood | A clean, dry surface. Contaminants may be removed by washing with cleaner and clean water. | |
This product may be applied by the following methods
| Spray: | Apply by airless spray. | |
| Brush: | Recommended | |
| Roller: | Suitable for small areas. | Not recommended for the first primer coat. Take care to achieve the specified dry film thickness. |
One-component
| Thinner: | Jotun Thinner No. 7 | / Jotun Thinner No. 10 / Jotun Thinner No. 2 |
| JOTUN Thinner No. 7 | JOTUN Thinner No. 2 |
Jotun Thinner No. 7 / Jotun Thinner No. 10: for winter use. Jotun Thinner No. 2
| JOTUN Thinner No. 2 | Summer use |
|---|
| Nozzle tip size (inch/1000): | 15-19 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
| Substrate Temperature | 5 °C | 10 °C | 23 °C | 40 °C |
| Touch Dry | 35 min | 25 min | 20 min | 15 min |
| Walk-on Dry | 3 h | 2.5 h | 2 h | 1.5 h |
| Minimum recoat interval | 3 h | 2.5 h | 2 h | 1.5 h |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Temperature
| Continuous | Peak | |
| Drying, atmospheric | 120°C | 140 °C |
Withstands peak temperatures for a maximum of one hour.
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous coat: | Alkyd, epoxy |
| Subsequent coat: | Alkyd |
| Volume | Container Size | |
| (L) | ||
| Pilot QD Primer Plus High-build Modified Alkyd Primer | 20 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Pilot QD Primer Plus 48 months. High-Build Modified Alkyd Primer
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
