Penguard Midcoat M20 S Fast-Drying Epoxy Micaceous Iron Oxide Intermediate Coat M20 S is an epoxy coating used as an intermediate coat. Recommended for use on wind turbine towers, refineries, power plants, buildings and mining equipment. It is a fast-drying, high-solids epoxy coating containing micaceous iron oxide. Parameters on this page: volume solids 77 ± 2%, dry film thickness 100-250 µm, theoretical spreading rate 7.7-3.1 m²/L. Comparable models from the same brand: Jota EP15 MIO fast-drying epoxy micaceous iron oxide intermediate coat, Penguard Express MIO 80 fast-drying epoxy micaceous iron oxide 80, Penguard Express MIO fast-drying epoxy micaceous iron oxide.
Parameter source: JOTUN original technical data sheet (TDS) for Penguard Midcoat M20 S Fast-Drying Epoxy Micaceous Iron Oxide Intermediate Coat M20 S; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 77 ± 2% |
|---|---|
| Dry Film Thickness | 100–250 µm |
| Theoretical Spreading Rate | 7.7–3.1 m²/L |
| VOC | 161 g/L (China) |
| Density / Specific Gravity | 1.6 kg/L |
| Number of Components | Two-component |
| Flash Point | 30 °C |
| Thinner | Jotun Thinner No. 17. Normally no thinning is required. In extreme environments… |
| Mixing Ratio | 5 parts : 1 part (by volume) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Penguard Midcoat M20 S
It is a two-component polyamine-cured epoxy coating. It is a fast-drying, high-solids epoxy coating containing micaceous iron oxide. It provides good levelling and improves film appearance. Suitable as an intermediate coat for new construction in atmospheric environments. Suitable for certified coating systems.
Suitable for steel structures exposed to corrosive environments. Recommended for use on wind turbine towers, refineries, power plants, buildings and mining equipment.
Others
Penguard Midcoat M20 Fast-Drying Epoxy Micaceous Iron Oxide Intermediate Coat M20 (0P7)
For the different products in this series, refer to the respective technical data sheets
Light grey, white, RAL 7035, RAL 9001, RAL 9010, RAL 9018
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 77± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 30 °C |
| Density | Theoretical Value | 1.6 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| China | Mandatory national standard of China | GB 30981.2-2025 | 161 g/L |
| Coating hazards GB | 30981.2-S-Pb≤1000-NC |
Contains reactive thinner
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 100–250 µm |
| Wet Film Thickness | 130–325 µm |
| Theoretical Spreading Rate | 7.7–3.1 m²/L |
When the dry film thickness is below 100 µm, more thinner is required.
Surface Preparation
| Substrate | Minimum | Recommended |
| Coated surface | A clean, dry and sound compatible primer. | |
The recommended surface preparation provides optimum properties including adhesion, corrosion resistance, heat resistance and chemical resistance.
This product may be applied by the following methods
| Spray: | Apply by airless spray. |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. |
| Penguard Midcoat M20 S Comp A — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component A | 5 parts |
| Penguard Midcoat M20 S Comp B — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component B | 1 part |
| Thinner | Jotun Thinner No. 17. Normally no thinning is required. For application in extreme environments, consult the local Jotun representative. Do not thin beyond local environmental regulations. |
|---|
| Nozzle tip size (inch/1000): | 17 -27 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
| Substrate Temperature | 5 °C | 10 °C | 23 °C | 40 °C |
| Touch Dry | 8 h | 5 h | 2 h | 1 h |
| Walk-on Dry | 24 h | 12 h | 5 h | 2 h |
| Minimum recoat interval | 24 h | 12 h | 5 h | 2 h |
| Dry/cured to service | 14 days | 10 days | 7 days | 3 days |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Dry/cured to service: the minimum time before the coating can be permanently exposed to a specific environment/medium.
| Paint temperature | 23 °C |
| Pot Life | 1 h |
Temperature
| Continuous | Peak | |
| Drying, atmospheric | 120°C | 140 °C |
Withstands peak temperatures for a maximum of one hour.
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous coat: | Inorganic zinc silicate shop primer, zinc epoxy, epoxy |
| Subsequent coat: | Polyurethane, epoxy, acrylic |
| Volume | Container Size | |
| (L) | ||
| Penguard Midcoat M20 S Comp A — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component A | 15 | 20 |
| Penguard Midcoat M20 S Comp B — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component B | 3 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Penguard Midcoat M20 S Comp A — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component A | 24 months |
| Penguard Midcoat M20 S Comp B — Fast-Drying Epoxy MIO Intermediate Coat M20 S, Component B | 24 months |
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
