Intershield 9G Epoxy Anti-slip Deck Coating belongs to epoxy coatings. Designed for areas requiring a rollable, durable, low solar-absorbing anti-slip deck coating that can be applied at low temperature. A low solar-absorbing, high-solids epoxy anti-slip deck coating with low-temperature application performance. Parameters on this page: volume solids 92% ± 2%, theoretical spreading rate 0.49-0.73 m²/L. Comparable models of the same brand: Intergard 361 Epoxy Paint, Intergard 5263 Epoxy Tie Coat, Intergard 7020 Abrasion-resistant Aluminium Pure Epoxy.
Parameter source: INTERNATIONAL original technical data sheet (TDS) for Intershield 9G Epoxy Anti-Skid Deck Coating; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 92% ± 2% |
|---|---|
| Dry Film Thickness | — |
| Theoretical Spreading Rate | 0.49–0.73 m²/L |
| VOC | 89 g/L (as supplied) (EPA Method 24). Volatile organic compound values are… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 4:1 (by volume) |
| Colour / Appearance | EGA950 dark grey |
| Gloss | Matt |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A low-solar-absorption, high-solids epoxy anti-skid deck coating with low-temperature application performance. Approved to meet the requirements of MIL-PRF-24667, Type VIII, Composition G.
Designed for areas requiring a roller-appliable, durable, low-solar-absorption, low-temperature-applicable non-skid deck coating.
For newbuilding, maintenance and repair, or in-service maintenance.
| Colour | EGA950 dark grey |
|---|---|
| Topcoat/gloss | Matt |
| Component B (curing agent) | EGA951 |
| Volume Solids | 92% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 4:1 (by volume) |
| Theoretical Spreading Rate | 0.49–0.73 m²/L, allowing for a suitable loss factor |
| Application Methods | Roller application |
| Flash Point | Component A 39 °C; Component B 39 °C; mixed 39 °C |
| Induction Time | N/A |
| Drying data | 0°C | 5°C | 15°C | 25°C |
| Hard dry [ISO 9117-1:2009] | 36 h | 24 h | 12 h | 6 h |
| Pot life after mixing | 45 min | 40 min | 35 min | 25 min |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 0°C | 5°C | 15°C | 25°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Interthane 990 | 36 h | 72 h | 24 h | 72 h | 12 h | 72 h | 6 h | 48 h |
| Interthane 990HS | 36 h | 72 h | 24 h | 72 h | 12 h | 72 h | 6 h | 48 h |
| Note | Drying times and pot life vary with ambient temperature and/or humidity. |
|---|
| Volatile Organic Compounds | 89 g/L (as supplied) (EPA Method 24). Volatile organic compound values are typical values, provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|---|
| Military specification | MIL-PRF-24667, Type VIII, Composition G |
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Typical paint systems: Intershield 486/Intershield 9G; Intershield 486/Intershield 9G/Interthane 990; Intershield 486/Intershield 9G/Interthane 990HS
Apply only to clean, dry surfaces. Remove all grease, oil, soluble contaminants and other foreign matter in accordance with the solvent cleaning standard (SSPC-SP1).
Intershield 9G is specifically designed as a rollable anti-skid coating, applied over suitably prepared Intershield 486. For surface preparation and recoating information, refer to the relevant product data sheet.
For specific advice, consult your local International Paint representative.
If required, apply with a smooth, phenolic-core roller to obtain a 'ploughed' effect. For other effects, consult International Paint.
Pour the mixed coating onto the suitably prepared surface, then spread evenly with a long-handled, smooth, phenolic-core roller.
Heavy films applied carelessly are prone to cracking and/or blistering.
After suitable application, Intershield 9G presents a uniform, rough appearance over the entire surface. There are no loosely adhered particle lumps. If desired, the surface roughness can exhibit a "ploughed field" pattern with peaks or ridges. The ridge peaks are approximately 0.5-1.0 in (12.5-25.0 mm) apart and approximately 1/16-3/32 in (1.5-2.4 mm) high. The anti-skid coating should be at least 30 mil (762 µm) thick at its thinnest point.
See the introductions for the following equipment:
Do not divide or mix the paint until ready to use. The paint is supplied as a unit in separate containers. Always mix the whole unit in the supplied ratio when using.
Stir the Intershield 9G coloured base (Component A) with a power mixer for 2 minutes, ensuring no aggregate remains at the bottom of the container. Add the Intershield 9G curing agent (Component B) and stir thoroughly with a power mixer for 3 minutes, stop stirring, and scrape the container walls and bottom. Take care not to introduce air into the coating.
Do not thin!
Use a smooth, phenolic-core roller sleeve.
International GTA415/GTA220
All equipment shall be cleaned with International GTA415/GTA220 immediately after use.
Pay close attention to the condition of the paint. Do not exceed the pot life after mixing.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; other regions — contact the regional office
Apply in good weather, with air and surface temperatures above 0 °C. The surface temperature shall be at least 3 °C above the dew point. For optimum application performance, bring the paint temperature to 21–27 °C before mixing and application.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 5 US gal | 4 US gal | 6 US gal | 1 US gal | 1.25 US gal |
All components are supplied in one 6 US gal container (a plastic bag on a plastic tray suspended above the pigmented base).
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 5 US gal | 83 lb |
| Shelf life | When stored in a protected environment at 4–38 °C, a minimum of 12 months from the date of manufacture, after which re-inspection is required. Store in a cool, dry place away from heat and ignition sources. |
|---|
Please consult INTERNATIONAL.
The information given in this product data sheet is not exhaustive. Anyone who uses, for any reason, any product other than those specifically recommended in this data sheet without first obtaining our written confirmation does so at their own risk as regards the suitability of the product for the intended purpose. Although we make every effort to ensure that all advice we give about the product (whether in this data sheet or otherwise) is correct, we cannot control the quality or condition of the substrate, nor the many factors affecting the application and use of this product. Accordingly, unless we specifically agree otherwise in writing, we accept no liability, to the maximum extent permitted by law, for any product performance problem arising, or for any loss or damage caused by use of the product. We therefore disclaim all warranties, express or implied, arising by operation of law or otherwise, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. All products supplied and all technical guidance provided are subject to our terms and conditions of sale. You should obtain a copy of this document and read it carefully. The information contained in this product data sheet may be amended at any time in the light of experience and of our continuing product development policy. Before using the product, it is the user's responsibility to check with the local representative that the data sheet in their possession is the latest version.
This technical data sheet is also available on our websites www.international-marine.com and www.international-pc.com, and should be consistent with this document. If there is any discrepancy between this document and the version of the technical data sheet on the website, the version on the website shall prevail.
© AkzoNobel, 2015www.international-marine.com
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
