HEMPEL's Avantguard Epoxy Zinc-rich Primer 860

Browse Similar Models by CategoryThis model belongs to: Primer, Zinc-rich Primer, Epoxy

Product Characteristics

Description

Hempel's Pioneer Shield Epoxy Zinc-rich Primer 860 is an active zinc-rich epoxy/epoxy resin primer complying with SSPC Paint 20 (2019) Type 2, Grade 1 and ISO 12944 Part 5 (2018). The product fully complies with ASTM D520 Type 2 and EU Directive 2004/42/EC "on the limitation of VOC emissions: subcategory j".

Recommended use

Hempel's Pioneer Shield Epoxy Zinc-rich Primer 860 is recommended for general use, providing long-term protection of steel exposed to highly to extremely corrosive environments (ISO 12944 Part 2). Suitable for offshore protection. The product cures quickly and can replace zinc-rich silicates used for atmospheric corrosion protection below 160 °C [320 °F].

Certificates / approvals

When used as part of a specified coating system, meets ISO 12944 requirements, Part 6 C5, Part 9 CX.

• When used as part of the specified coating system, meets the requirements of NORSOK M-501.

Edition 6, System 1. Edition 7, System 1B.

Product features

• Reduces the effects of corrosion and provides excellent galvanic protection.

• Fast drying, with the shortest overcoating interval.

- Excellent mechanical strength, also under cyclic temperatures, with high flexibility and a self-healing effect improving tolerance of high film thickness.

• Excellent tolerance of high relative humidity during application.

• Cures at temperatures down to -10 °C [14 °F].

• High-zinc shade 1984A, with a zinc dust content in the dry film of not less than 90%.

VOC content (after mixing the multi-component paint)

Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.

Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.

For professional use only.

Product Data

Curing agent 98384_______________________________

_______________________________

Surface Preparation

Cleanliness

• Remove oil, grease and other contaminants by cleaning with a suitable cleaner.

• Remove salts, detergents and other contaminants by high-pressure fresh water washing.

New construction

• Abrasive blast clean to Sa 2½ (ISO 8501-1) / SP 10 (SSPC) minimum.

• Remove dust, blast abrasives and loose material.

Roughness

• Surface roughness Medium (G) (ISO 8503-2).

For further details, refer to the separate Hempel document Surface Preparation Guide.

Application

Mixing Ratio

Base 17999 : curing agent 98384 (8.5 : 1.5 by volume)

Products containing floating or settling particles/pigments require continuous stirring during application; this is especially important when heavily thinned.

Pot Life

Recommended method

If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)

Film thickness

Excessive thickness must be strictly controlled; local thickness must never exceed 200 µm [8.0 mils] DFT. On irregular surfaces, take particular care to avoid over-application.

Application conditions

• During application, the product temperature must be above 15 °C [59 °F].

• The surface to be coated must be clean and dry, and its temperature must be at least 3 °C [5 °F] above the dew point to avoid condensation.

• During application and curing, the surface temperature must be above -10 °C [14 °F].

Relative humidity

• During curing, the relative humidity must be below 95%.

• During application, the relative humidity must be below 95%.

Drying and recoat

Product compatibility

• Previous coat: none.

• Subsequent coat: none, or according to Hempel's specifications.

Drying Time

Measured at 60 µm dry film thickness under standard conditions; see Hempel's explanatory notes.

Recoat

For products of the same generic chemical composition, recoat times are for reference only.

For further information, refer to Hempel's specifications.

Drying conditions

- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.

• Avoid condensation on the freshly applied coating.

Recoat notes

• If the maximum recoat interval is exceeded, the surface must be roughened to ensure intercoat adhesion.

• Before recoating, remove zinc salts or other contaminants.

• The surface must be dry and clean before application.

Others

• Hempel's specifications supersede any recommendations in the Product Data Sheet.

Storage

Shelf Life

When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.

Storage conditions

- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.

Carbon footprint

Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².

The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.

Calculated based on the standard colours defined in this PDS. Values may vary with colour.

Supplementary documents

For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:

• Notes to the Product Data Sheet.

• Application Methods
• Surface preparation
• the Application Instructions for this product.

• Repair and maintenance.

• Inspection and quality control.

datasheet, which is also available for download at www.hempel.com.

This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):

If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.

Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.