HEMPEL's Acrylic Enamel 5636E

Browse Similar Models by CategoryThis model belongs to: Topcoat, Acrylic

5636E

Product Characteristics

Description

HEMPEL Acrylic Enamel 5636E is a fast-drying topcoat based on acrylic resin and non-chlorinated plasticiser, with desirable gloss and colour retention. Physically drying. Resistant to seawater and to splashes of aliphatic hydrocarbons and animal and vegetable oils.

Recommended use

For use as an intermediate coat or topcoat in on-site container application. As part of the HEMPEL waterborne container coating system

marking paint for use with

Service temperature

• Under dry conditions: maximum service temperature 80 °C [176 °F].

VOC content

Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.

Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.

For professional use only.

Product Data

Black 19990

Surface Preparation

Cleanliness

• The surface must be dry and clean before application.

New construction

• In accordance with Hempel's specifications.

For further details, refer to the separate Hempel document Surface Preparation Guide.

Application

Mixing Ratio

Stir thoroughly before use.

5636E

Recommended method

Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)

Film thickness

Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval. To achieve optimum performance, avoid excessive film thickness.

Application conditions

• The surface to be coated must be clean and dry, and its temperature must be at least 3 °C [5 °F] above the dew point to avoid condensation.

• Provide adequate ventilation during application and drying.

Relative humidity

• During application, the relative humidity must be below 85%.

• During curing, the relative humidity must be below 85%.

Notes

• Two coats of topcoat may be required to achieve full hiding.

Drying and recoat

Product compatibility

• Previous coat: according to Hempel's specifications.

• Subsequent coat: none.

Drying Time

Measured at 35 µm dry film thickness under standard conditions; see Hempel's explanatory notes.

Recoat

For products of the same generic chemical composition, recoat times are for reference only.

For further information, refer to Hempel's specifications.

Drying conditions

- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.

• Avoid condensation on the freshly applied coating.

Recoat notes

• The surface must be clean before recoating.

Others

• Hempel's specifications supersede any recommendations in the Product Data Sheet.

Storage

Shelf Life

When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.

Storage conditions

5636E

Carbon footprint

Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².

The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.

Calculated based on the standard colours defined in this PDS. Values may vary with colour.

Supplementary documents

For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:

• Notes to the Product Data Sheet.

• Application Methods

datasheet, which is also available for download at www.hempel.com.

This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):

If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.

Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.