Hempel Solvent-free Phenolic Epoxy Lining 430 is an epoxy paint. Suitable for various markets, including but not limited to: oil and gas, chemical processing, power generation, mining, pulp and paper, and water and wastewater treatment. Can withstand crude oil/water mixtures at temperatures up to 90 °C [195 °F]; can be sprayed in one pass with a single-leg airless pump and put into service in less than 72 hours. Parameters on this page: volume solids 100%, dry film thickness 500 µm, theoretical spreading rate 2 m²/L. Comparable products of the same brand: Hempel Solvent-free Phenolic Epoxy Lining 630, Hempel Reinforced Phenolic Epoxy Glass Flake 640, Hempel Phenolic Epoxy Vinyl Ester Glass Flake 740.
Data source: HEMPEL original Technical Data Sheet (TDS), "Hempel Solvent-free Phenolic Epoxy Lining 430"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 100% |
|---|---|
| Dry Film Thickness | 500 µm |
| Theoretical Spreading Rate | 2 m²/L |
| VOC | 25 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 77°C |
| Colour / Appearance | White 10000 ** |
| Gloss | Semi-gloss |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Hempel Solvent-free Phenolic Epoxy Lining 430 is a high-performance phenolic epoxy lining. This product is 100% solids, can be applied in high build, and provides temperature and chemical resistance under long-term immersion conditions.
Can withstand crude oil/water mixtures at temperatures up to 90 °C [195 °F]; can be sprayed in one pass with a single-leg airless pump and put into service in less than 72 hours. Can also be used to build glass-fibre-reinforced lining systems.
Used as a lining for new tanks and pipelines, or for maintenance.
Can withstand a wide range of chemicals, including but not limited to: crude oil, refined hydrocarbons, aviation fuel, gasoline (petroleum) mixtures, biodiesel, MTBE (methyl tert-butyl ether), produced water, alcohols, aliphatic and aromatic solvents, specific caustic solutions and aqueous solutions.
Suitable for various markets, including but not limited to: oil and gas, chemical processing, power generation, mining, pulp and paper, and water and wastewater treatment.
search=Hempel&page=0.
| Product safety | Flash point 77 °C |
|---|
| Regulations | Value |
| European Union | 25 g/L |
| USA (coatings) | 25 g/L |
| USA (regulatory) | 25 g/L |
| China | 25 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 37750 |
|---|---|
| Product components | Base 37759 |
Curing Agent 9782S
| Standard colour* / code | White 10000 ** |
|---|---|
| Gloss | Semi-gloss |
| Volume solids | 100% |
| density | 1.4 kg/L |
| Recommended dry film thickness | 500 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 37759 : Hardener 9782S (4 : 1 by volume)
Stir thoroughly before use. Thinning is not permitted.
Thinner
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
|---|
| Product temperature | 20°C | 10°C | 30°C |
| Pot Life | 50 min | 80 min | 20 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | No thinning required | Nozzle pressure: 20 MPa; nozzle size: 0.53–0.74 mm |
| Brush/roller | No thinning required | Not applicable. |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. For tank linings, brush and roller application must be limited to touch-up, repair areas or minor repairs. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 300 µm | 750 µm | 500 µm |
| Wet Film Thickness | 300 µm | 750 µm | 500 µm |
| Theoretical Spreading Rate | 3.3 m²/L | 1.3 m²/L | 2 m²/L |
Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval. To achieve optimum performance, avoid excessive film thickness.
- Preceding coats: none or according to Hempel's specification. Recommended products: Hempaline Prepare 130, Hempaline Prepare 110 - Subsequent coats: none or according to Hempel's specification. Recommended products: Hempaline Defend 430
| Surface temperature | 10°C | 20°C | 30°C | 40°C |
| Touch Dry | 8 h | 4 | 2 | 1 |
| Hard Dry | 24 h | 12 | 5 | 2½ |
| Fully cured | 7 days | 3 | 2 | 1 |
Measured at 500 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 10°C | 20°C | 30°C | 40°C | |
| Immersion | |||||
|---|---|---|---|---|---|
| Hempaline Defend 430 | Minimum | 8 h | 4 h | 2 h | 60 min |
| Maximum | 30 days | 21 days | 14 days | ||
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
- For tank linings, if the maximum recoat interval is exceeded, roughen the surface by blasting to ensure intercoat adhesion.
| Ambient temperature | 25°C |
| Binder | 18 months |
| Curing agent | 18 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 6.6 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
