HEMPEL Silicone Repair Paint 27500 is a silicone coating. It can also be recommended as a low-temperature tie coat, used with HEMPEL Silicone Fouling Release Sealer 27400, for full system application with Hempaguard®/Hempasil/Hempablue topcoats. HEMPEL Silicone Repair Paint 27500 is a high-solids tie coat compatible with Hempaguard®/Hempasil and Hempablue topcoats. Parameters on this page: volume solids 65 ± 2%, dry film thickness 120 µm, theoretical spreading rate 5.5 m²/L. Comparable models from the same brand: HEMPEL Silicone 88710, HEMPEL Silicone Fouling Release Sealer 27400, HEMPEL Silicone Fouling Release Sealer 27700.
Parameter source: HEMPEL original technical data sheet (TDS) for HEMPEL Silicone Repair Paint 27500; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 65 ± 2% |
|---|---|
| Dry Film Thickness | 120 µm |
| Theoretical Spreading Rate | 5.5 m²/L |
| VOC | 251 g/L (China) |
| Density / Specific Gravity | 1.2 kg/L |
| Number of Components | — |
| Flash Point | 28°C |
| Colour / Appearance | Yellow 23410 |
| Gloss | Semi-gloss |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
27500
HEMPEL Silicone Repair Paint 27500 is a high-solids tie coat compatible with Hempaguard®/Hempasil and Hempablue topcoats.
HEMPEL Silicone Repair Paint 27500 is the tie coat for Hempaguard®/Hempasil/Hempablue topcoats, complies with the FLEX specification, and can be used for touch-up and repair of damaged areas of existing silicone topcoats, ensuring adhesion between the anticorrosive system and the Hempaguard®/Hempasil/Hempablue topcoat. Minimum curing temperature: 0 °C [32 °F].
It can also be recommended as a low-temperature tie coat, used with HEMPEL Silicone Fouling Release Sealer 27400, for full system application with Hempaguard®/Hempasil/Hempablue topcoats. The minimum curing temperature of this system is 0 °C [32 °F].
| Product safety | Flash point 28 °C |
|---|
| Regulations | Value |
| European Union | 251 g/L |
| USA (coatings) | 249 g/L |
| USA (regulatory) | 249 g/L |
| Canada | 249 g/L |
| China | 251 g/L |
| Hong Kong | 249 g/L |
| South Korea | 251 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 27500 |
|---|---|
| Standard colour / code | Yellow 23410 |
Cream 23410
| Gloss | Semi-gloss |
|---|---|
| Volume solids | 65 ± 2% |
| density | 1.2 kg/L |
| Recommended dry film thickness | 120 µm |
27500
Stir thoroughly before use. Thinning is not permitted. The shelf life of this product should be understood as the time from opening the container until the product is no longer suitable for application
Thinner
| Cleaning solvent | HEMPEL's Thinner 08080 |
|---|
| Product temperature | 20°C | 0°C | 40°C |
| Pot Life | 60 min | ||
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | No thinning required | Nozzle pressure: 15 MPa; nozzle size: 0.48–0.53 mm |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 153 µm | 183 µm | |
| Theoretical Spreading Rate | 6.5 m²/L | 5.5 m²/L | |
Achieving the specified minimum dry film thickness uniformly is essential. To obtain optimum performance, avoid excessive film thickness.
- Previous coat: according to Hempel's specification. Recommended products: HEMPEL Epoxy 15570, HEMPEL Silicone Fouling Release Sealer 27400 - Subsequent coat: according to Hempel's specification. Recommended products: silicone fouling release,
Silicone®.
| Surface temperature | 10°C | 20°C | 30°C |
| Hard Dry | 4½ h | 2¼ | 1½ |
| Fully cured | 4 days | 2 | 1½ |
Dry film thickness 120 µm measured under standard conditions; see Hempel's explanatory notes for details.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 10°C | 20°C | 30°C | |
| Immersion | ||||
|---|---|---|---|---|
| HEMPEL Silicone Repair Coating 27500 | Minimum | 20 h | 6 h | 5 h |
| Maximum | 72 h | |||
| HEMPEL's Silicone Antifouling Hempaguard X7 89900 | Minimum | 21 h | 8 h | 6 h |
| Maximum | 48 h | |||
| HEMPEL's Third-generation Silicone Foul-release Coating Hempasil X3+ 87500 | Minimum | 21 h | 8 h | 6 h |
| Maximum | 48 h | |||
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
27500
| Ambient temperature | 25°C |
|---|---|
| Product | 18 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| GWP (Global Warming Potential) | 11.2 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
