Hempel Epoxy Zinc-rich Paint 1536C is a zinc-rich primer, an epoxy coating system. This product can be used as an epoxy zinc-rich primer and epoxy zinc-rich shop primer according to the coating specification. Hempel Epoxy Zinc-rich Paint 1536C is a two-component polyamide-cured zinc-rich epoxy primer. Parameters on this page: volume solids 47 ± 2%, dry film thickness 30 µm, theoretical spreading rate 16 m²/L. Comparable products of the same brand: Hempel Epoxy Zinc-rich Primer, Hempel Pioneer Shield Epoxy Zinc-rich Primer 550, Hempel Pioneer Shield Epoxy Zinc-rich Primer 650.
Data source: HEMPEL original Technical Data Sheet (TDS), "Hempel Epoxy Zinc-rich Paint 1536C"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 47 ± 2% |
|---|---|
| Dry Film Thickness | 30 µm |
| Theoretical Spreading Rate | 16 m²/L |
| VOC | 446 g/L (China) |
| Density / Specific Gravity | 2.3 kg/L |
| Number of Components | Two-component |
| Flash Point | 30°C |
| Thinner | HEMPEL's Thinner 08450 |
| Colour / Appearance | Grey-red 19830 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
1536C
Hempel Epoxy Zinc-rich Paint 1536C is a two-component polyamide-cured zinc-rich epoxy primer. It forms a hard, abrasion-resistant and highly weather-resistant film. This product provides cathodic protection for locally damaged areas. The dry film zinc content of this product reaches 80 ± 2% (by weight).
This product can be used as an epoxy zinc-rich primer and epoxy zinc-rich shop primer according to the coating specification.
| Product safety | Flash point 30 °C |
|---|
| Regulations | Value |
| European Union | 446 g/L |
| USA (coatings) | 446 g/L |
| USA (regulatory) | 446 g/L |
| China | 446 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 1536C |
|---|---|
| Product components | Base 1536R |
Curing Agent 9574C
| Standard colour / code | Grey-red 19830 |
|---|
Grey 19830
| Volume solids | 47 ± 2% |
|---|---|
| density | 2.3 kg/L |
| Recommended dry film thickness | 30 µm |
1536C
Base 1536R : Hardener 9574C (4 : 1 by volume)
Products containing floating or settling particles/pigments require continuous stirring during application; this is especially important when heavily thinned.
| Thinner | HEMPEL's Thinner 08450 |
|---|---|
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
| Product temperature | 20°C |
|---|---|
| Pot Life | 8 h |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 5% | Nozzle pressure: 15 MPa; tip size: 0.43–0.53 mm |
| Air Spray | 5% | Not applicable. |
| Brush | 5% | Not applicable. |
If brushing or rolling is used, multiple coats are required to achieve the specified dry film thickness. Do not thin the components separately - the mixture may be thinned after mixing. When used as a shop primer, the thinning amount is limited to a maximum of 80% by volume.
Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 21 µm | 106 µm | 64 µm |
| Theoretical Spreading Rate | 47 m²/L | 9.4 m²/L | 16 m²/L |
Depending on the intended use and application area, the product may be specified at film thicknesses other than those indicated. This will change the spreading rate, drying and curing time and overcoating interval. Excessive thickness must be strictly controlled; locally never exceed 50 µm [2.0 mils] DFT. On irregular surfaces, special attention is recommended to avoid over-application.
| Surface temperature | 20°C |
| Surface Dry | 30 min |
| Hard Dry | 5 h |
| Through dry | 8 h |
| Fully cured | 7 days |
1536C
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 10°C | 20°C | 30°C | 40°C | |
| Atmospheric, mild | |||||
|---|---|---|---|---|---|
| HEMPEL's Epoxy Primer 1530C | Minimum | 5 h | 2 h | 60 min | 40 min |
| Maximum | No maximum | ||||
| Atmospheric, moderate | |||||
| HEMPEL's Epoxy Primer 1530C | Minimum | 5 h | 2 h | 60 min | 40 min |
| Maximum | No maximum | ||||
| Atmospheric, severe | |||||
| HEMPEL's Epoxy Primer 1530C | Minimum | 7½ h | 3 h | 90 min | 55 min |
| Maximum | 75 days | 30 days | 15 days | 9 days | |
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 12 months |
| Curing agent | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| GWP (Global Warming Potential) | 17.2 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
1536C
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
