6035 EPICON T-800 HOLDING PRIMER Epoxy Phenolic Resin Temporary Holding Primer belongs to epoxy coatings and is used as a primer. EPICON T-800 HOLDING PRIMER is a coating made from epoxy phenolic resin, anti-corrosive pigments and curing agent. Parameters on this page: volume solids 37 ± 2%, DFT 25 µm, theoretical spreading rate 0.067 L/m². Similar models from the same brand for comparison: 1034 EPICON ZINC RICH PRIMER B-2 Epoxy Zinc-rich Primer, 1036 UNIZINC 80 Special Epoxy Zinc Dust Primer, 5113 EPICON ZINC HB-2 Epoxy Zinc Dust Primer.
Parameter source: CMP original technical data sheet (TDS) '6035 EPICON T-800 HOLDING PRIMER Epoxy Phenolic Resin Temporary Holding Primer'; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 37 ± 2% |
|---|---|
| Dry Film Thickness | 25 µm |
| Theoretical Spreading Rate | 0.067 L/m2 |
| VOC | 581 g/L |
| Density / Specific Gravity | 1.19 g/ml |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER B |
| Mixing Ratio | Base : curing agent = 85:15 (by volume) |
| Colour / Appearance | Powder brown |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
EPICON T-800 HOLDING PRIMER is a coating made from epoxy phenolic resin, anti-corrosive pigments and curing agent.
It provides chemical resistance to seawater, petroleum products, crude oil, alkalis and weak acids. It can be used with EPICON T-800 as an effective cargo hold primer applied inside cargo tanks.
| Type | Epoxy Phenolic Resin Temporary Holding Primer |
|---|---|
| Use | Can be used as a temporary rust-preventive primer on the interior of chemical cargo tanks. |
| Mixing Ratio | Base : curing agent = 85:15 (by volume) |
|---|---|
| Colour | Powder brown |
| Flash Point | Base 17.5°C; Curing Agent 8.0°C |
| Density | 1.19 g/ml |
| Volume Solids | 37 ± 2% |
| Volatile organic compound content | 581 g/L |
| Theoretical spreading rate | 0.067 L/m2 |
| Thickness | WFT 67 µm; DFT 25 µm |
(dry film 25 µm)
| Temperature | 10 °C | 20 °C | 30 °C | 40 °C | |
| Drying Time | Surface Dry | 15 min | 10 min | 6 min | 3 min |
| Hard Dry | 3 h | 2 h | 1.5 h | 30 min | |
| Recoat interval | At least | 16 h | 8 h | 5 h | 3 h |
| At most* | 28 days | 21 days | 15 days | ||
| At most** | 10 days | 7 days | 5 days | 3 days | |
| Pot life | 24 h | 16 h | 12 h | 8 h | |
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | Minimum 10 °C |
| Humidity | Maximum 85% RH; steel temperature at least 5 °C above the dew point |
| Airless spray: viscosity | 9–10 s (Ford Cup #4) |
| Nozzle | Graco719 |
| Paint output pressure | 8.8-11.8 Mpa |
| Spray gun speed | 60–160 cm/s |
| Thinner | EPOXY THINNER B |
| Thinning | 0–25% by volume |
| Newbuilding | Follow the shipyard standards. Consult your CMP representative for advice. |
|---|---|
| Repair and maintenance | Remove oil and grease. Remove salts and other contaminants with high-pressure clean water, then dry |
| Fully. Remove damaged areas by abrasive blasting to at least Sa 2½ (ISO 8507-1 | 2007) or by |
| power tool to St3 (ISO 8507-1 | 2007). |
| Rinse with water | Consult your CMP representative for advice. |
The type and degree depend on the actual condition of the material and the required performance.
Optimum results can be achieved even on lightly corroded or damp steel surfaces.
Use standards consistent with the Worldwide Marine Specifications.
| Preceding coat | CERABOND 2000 |
|---|---|
| Subsequent coat | EPICON T-800, EPICON T-800 QD |
| Packaging | Two-component |
Note: 1. In confined spaces or restricted spaces at low temperature, ventilation is necessary to remove volatilised solvent and promote film formation during application and drying.
2. Stir the base with an electric stirrer to a uniform state, then thoroughly stir all of the curing agent with the base. Finally add an appropriate amount of thinner and mix thoroughly.
3. Excessive solvent may reduce sag resistance. 4. Mix only the amount of paint that can be used within the specified pot life.
5. *(1) Shade netting is recommended over the coating surface to avoid direct sunlight through manholes or other openings.
6 **Data obtained under outdoor exposure.
7 Volume solids, volatile organic content and density are theoretical values calculated from the formulation without thinner.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
